ALLIED FOAM TECH
CORP. (SINCE 1994) Best Fire Rated Foam Products per ASTM-E119 Test |
In 2024 Allied Developed the Best Fire Rated Foam Composites per ASTM-E119 Test (see below) |
(non-brittle, vermiculite-free & no rust) |
Viable Products: Fire Barrier Boards, Cabinets, Doors, Partition Panels, Fire Barrier Sprayables (Precast & Cast-in-Place) |
MISSION STATEMENT |
Performance of currently available fire rated building materials,
tested under commonly used thicknesses and densities, are
really limited or inadequate in an actual fire. |
Allied powerful fire barrier foam technologies/composites* could really have a chance to significantly
reduce financial losses, save lives and save the environment
during an actual fire. |
* confirmed recently by a major thermal testing lab. at just 1" (2.5 cm) thickness on a steel H beam per ASTM-E-119 test |
FIRE HAZARD & TOXIC FUME RELEASE OF FLAMMABLE EXTERIOR BLDG. COMPOSITES |
(Effective fire barrier composites could avoid or significantly reduce the fire advancement) |
(17,000 Californians to be striped of Fire Insurance (8, 2024) |
|
||||
California, 8, 2024 | Colorado, 12, 2021 | Tianjin, 8, 2023 | Dubai, 11,2022 | London, 6, 2017 |
Allied fire barrier foam has the highest compressive and
bending strengths vs autoclaved & cast-in-place foam cement |
Cement Composite | Cure Condition | Density | Compr. Strength | Bending Strength |
AFT Fire Barrier Foam I | RT | 35 pcf | 900 - 1,000 psi | 370 - 500 psi |
AFT Fire Barrier Foam II | RT | 35 pcf | 650 - 750 psi | 300-350 psi |
AFT Portland Cem I/II | RT | 35 pcf | 400 - 450 psi | 100-200 psi |
Autoclaved Concrete | Autoclaving | 35 pcf | 600 - 700 psi | 100 psi(?) |
Allied fire barrier foam has the highest fire rating per
ASTM-E-119 Test against fire rated X-gypsum boards |
Allied fire barrier foam has twice or better fire ratings per
ASTM-E-119 Test over all fire rated intumescent coatings |
ASTM-E-119 Tested H-Beams with Fire Rated Coatings |
H
Beam with Allied Fire Barrier Foam - 4 Hours to 2,000oF |
H Beam with Intumescent Coating
- 2 Hours to 1,850 o F |
Allied Fire Rated Foam Slurries Can be Cast as Panels or Sprayed onto Steel Structures |
|
|
|
|
`
Fire rated, easy to handle, allow for pre-cast or cast-in-place manufacture. |
Fire rated, easy to handle, allow for pre-cast or cast-in-place manufacture. |
Sprayable with good adhesion to steel, non-hazardous, no rust & solvent free. |
Sprayable with good adhesion to steel, non-hazardous, no rust & solvent free. |
Excellent Bond Strengh (>> 1,000 psf ) of Allied 35 pcf (565 kg/m3) Fire Barrier Foam to A-36 Steel |
for > 420 feet (128 meters) Buildings Applications per SFRM (Spray-applied Fire Resistant Material) |
OTHER HIGHLIGHTS |
|||||||||||||||||||||
HIGHLIGHT - JANUARY, 2016 (World Trade Center Phase II Project, New York) Versatile Compact Foam Cement Mixing Pumping Setup - High Mobility with Good Output |
|||||||||||||||||||||
|
Landscape Architechture on the Roof - An application with allied low slump foam cement | ||||||||
Harvard University - NorthWest Science Building, 530,000 ft2 multidisciplinary research facility | ||||||||
The World's 1st Low Slump Geotechnical Roof Fill used Allied's Cement Composite Design, Foam Products & Machinery. | ||||||||
The award winning facility places more than half the total square footage of the facility below grade, and incorporates three functioning green roofs. The south facade of the Northwest Science Building defines a new South Yard, equipped with low landscape furniture. The yard is a green roof over extensive basement levels, with skylights bringing daylight into the underground areas. |
||||||||
|
||||||||
(Pre-project mockup work by Allied Foam Tech is shown below) |
Mixing & Pumping of High | Applying of High Slump Loss | Finished Foamed Cement Crown | Cross-section of |
Slump Loss Foam Cement | Foam Cement on 1 Vertical/4 Horizontal Slope | On Highly Sloped Geofoam | Landscape after ~ 1 year |
Our Mission |
At Allied we are committed to the continuing development of versatile and highly stable aqueous foam and systems with a wide range of properties and applications that meet the specific needs of our customers in the various industrial sectors. |
Technology |
Allied Foam Tech has developed a universal foam technology for a wide range of
industrial and
environmental applications. The excellent stability and dynamic nature
of Allied's make them ideal for use in
reducing the weight of cement/concrete, ceramics, firebricks,
adhesives, coatings, and binders. Foam stability derived from Allied's
many foam systems usually outranks that of any other existing
technologies available in today s marketplace. The
AFT
series of foam agents, using compressed air and Allied foam
generating equipment, generates very fine and stable foams. They are used
for the manufacture of lightweight
(or foamed) concrete, lightweight ceramics, insulative
firebricks, alternative landfill cover, foam coatings, foam adhesives,
long-duration firefighting foams and other uses. Substrates such as
cement, concrete, coating formulations or others that incorporate
Allied's foam products usually exhibit reduced weight with improved
workability, insulation value, sound proofness, and expanded
applications. Allied has also developed various models of compact and versatile foam generating equipment for production or field application that can be manually or remotely controlled. |